Six weld checks to run before you approve a cage sample

· KAIYU PET CAGES

Most cage failures start at a weld, not in the middle of a wire. Before you approve a sample, check the welds at the frame, the door and the base, because those six checks will tell you more than a general look at the cage.

A weld is the joint that holds wire to wire and wire to frame, and it is the point where strength, shape and safety meet. A good weld is small, even and fully joined, and it holds when the cage is lifted, pushed and used every day. A poor weld may look fine in a photo, but it can break in transport or leave a sharp point. The production run will repeat the same weld pattern as the sample, so a problem you miss on the sample will appear again in every cage in the order. That is why a buyer should spend a few minutes on the welds before signing off a sample, rather than finding the problem after delivery.

Look at every weld before you test the cage

Start in good light and look at the cage from the inside and from the outside. Count the welds at each corner and compare the left side with the right side, because a missing weld is easy to miss when you only look at one side. A missing weld leaves a wire free to move, and that movement will open a gap, make the panel feel loose and put extra load on the welds that are present. Look for welds that are too small, too large or uneven in size, because a weld that varies a lot from joint to joint often means the welding was rushed or the settings were not stable. A good weld should look similar at every joint of the same type.

The next check is for a cold weld, which is a weld that sits on the surface but does not join the metal underneath. It often looks dull, raised or lumpy, and you can sometimes see a dark line or a gap between the wire and the frame. A cold weld may hold when new, but it can break when the cage is lifted or pushed. Look closely at the joints where a thin wire meets a thick frame, because those joints are the hardest to weld well and the most likely to be cold. If you see a weld that does not blend into the metal on both sides, raise it with the supplier before you approve the sample.

A third check is for burn through and holes. When a weld is too hot, it can melt through a thin wire and leave a hole, a thin spot or a sharp edge. That hole weakens the wire and can cut a paw or a beak. Look for dark spots, small holes and thin areas at the center of a weld, and run a finger carefully along the inside of the joint to feel for a rough edge. If the wire feels thinner at the weld than it does a short distance away, the weld has damaged the wire and the joint should not be approved.

Test the joints that carry weight every day

The fourth check is for spatter and sharp points. Spatter is the small balls of metal that can land near a weld during welding, and they can feel sharp, look rough and cut through a coating. Check the inside of the cage first, because that is where a pet will touch the weld, and check the door frame, the tray rails and the corners where a hand will reach during cleaning. A weld should be smooth to the touch after finishing, with no loose balls of metal and no sharp point that catches your finger. If you find spatter, ask whether it will be cleaned off in production.

The fifth check is for cracks at and near the weld. A crack can be very fine, and it often starts at the edge of a weld and runs into the wire or into the frame. Look for a thin dark line that does not wipe off, and look again after you move the cage, because a crack can open slightly when the joint is stressed. Cracks are most common where a panel meets a rigid frame, where a door hinge meets a door, and where a stackable cage meets the cage below it. A cracked weld will grow with use, so it should not be approved.

The sixth check is for the welds that carry weight every day. Lift the cage by the top, push it gently from the side, open and close each door several times, and pull the door outward to check that the latch stays shut. Slide the tray in and out, lift the base and check that the frame stays square and does not twist. Pay close attention to the door hinges, the latch plate and the base corners. If a joint flexes, rattles or feels loose, the welds at that joint are not holding the frame as they should, and the problem will get worse after shipping and after months of daily use.

Check the finish and the frame after the welds

After you have checked the welds themselves, check how the finish covers them. A powder coated surface or a galvanized layer should cover the weld evenly, without a bare spot, a thin patch or a bubble. A bare spot at a weld is the first place to rust in a humid room, and a bubble in the coating can hide rust underneath. Look for white spots on a galvanized finish and for peeling on a powder coated finish. Ask the supplier whether the coating was applied before or after welding, and how the weld areas were treated after welding, because a weld that is coated before it is cleaned will trap dirt under the finish.

Finally, check the frame for shape after welding. A cage that has been welded unevenly can twist, so one corner sits higher than the others, a door does not close evenly, or a tray does not slide straight. Put the sample on a flat floor and check that all four feet touch at the same time. Open and close the doors and check that the gap around each door is even on all sides. If the frame is twisted, the doors and the tray will never work well. Ask the supplier to state the weld method and the weld positions on the drawing, so the sample you approve and the production run you receive are judged against the same document. This depends on the specification and needs confirmation against the drawing, including where each weld should be and how it should be finished.

A heavy duty stackable double dog cage like KY-P0039 shows why these checks matter in practice, because its welded wire body and feed bowls put extra load on the frame when two compartments are used side by side and when the cage is stacked. For that kind of cage, the buyer should confirm the welds at the divider, at the base and at the door hinges together, and approve the sample only when all six checks pass on the same sample. We build to the drawing, with MOQ 500 pcs and a lead time of 35 days, and a change to the weld pattern counts as a specification change. That single check, done before production, prevents most of the problems that appear later as loose doors, bent frames and returns.

Sourcing pet cages for your market? Send us the model and quantity — we reply within one working day.

Request a Quote

← All news

Message Email